The point of multi-spindle fastening is that one press completes many positions at once, and how closely those positions can sit depends on how close the spindles can be brought together. That distance is not a matter of habit or judgement: it is constrained by the bit, the spindle body, the connecting structure and the process. Only by working out the minimum centre distance can you judge whether a product is suited to multi-spindle fastening at all.
1. Four dimensional layers set the minimum centre distance
- Bit outer diameter: a cross-head bit with its guide sleeve is noticeably larger in diameter than the screw size itself, and a screw gripper or vacuum pick-up adds another ring;
- Spindle body: the body of a pneumatic or servo spindle is generally wider than the bit, and in most designs this is the layer that actually sets the limit;
- Connecting structure: the plates linking spindle to spindle, floating joints and guide bushes all consume thickness;
- Clearance envelope: the space required by gripper motion during the press stroke and by the sweep of the screw feed tube.
The usable minimum centre distance is set by the largest of these four layers, not by the bit diameter. Based on the company's current project experience, it commonly falls in the 25 to 40 millimetre range; the actual figure must be confirmed against screw size, bit type and spindle type, and should not be assumed.
2. Interference has three layers to check
1. Static interference
The actual clearance between spindle and spindle, and between spindle and connecting plate, in the assembled state. This layer is the easiest to find — a 3D model reveals it — and the easiest to mistake for the only thing that needs checking.
2. Dynamic interference
The envelope swept by guide sleeves, grippers and feed tubes through the full Z stroke. Many designs show no interference at rest yet collide as soon as the head descends, because the motion envelope was never checked.
3. Process interference
Protruding heads of screws already driven at neighbouring positions, washer diameters, ribs and recesses on the part surface. This layer is the most often overlooked and typically surfaces only at trial production, where rework is most expensive.
The method is to build a full-stroke envelope for each spindle and run a boolean check in 3D, then add a second virtual body at the worst-case screw head height. Time spent up front is far cheaper than reworking a fixture later.
3. Fixed pitch or adjustable pitch
- Fixed pitch: better stiffness, stable accuracy and lower cost. Suited to long-term production of one product, or to several products that share the same hole matrix.
- Adjustable pitch: spindles mounted on slots or quick-change base plates can be set per product. Flexible, but every adjustment introduces new positional error, and an adjustable structure is usually less rigid than a machined one-piece plate.
A workable compromise is grouped adjustment: spindles are divided into groups, fixed within a group and adjustable between groups. Changeover only moves the groups, preserving stiffness while keeping flexibility.
4. Fixtures must be designed together with spindle pitch
- Locating accuracy must be tighter than pitch tolerance: positional error of the part in the fixture adds directly to hole position error, and both cannot consume the same tolerance budget;
- Flatness must be controlled: with many points pressed at once, excessive height variation across the part leaves some spindles unable to reach depth. Floating bits are the usual remedy, but floating travel only absorbs small deviations; larger variation needs the fixture to level the part;
- Inclined surfaces need separate treatment: on a slope the spindle axis does not coincide with the hole axis, generating side load. Either locate the angle in the fixture or use a bit that can articulate;
- React the force: a multi-spindle press generates several times the reaction of a single spindle, so the fixture needs support pillars behind the critical points.
5. When multi-spindle is the wrong answer
- Positions are sparse and widely spread: the connecting plate becomes large and heavy, inertia rises and takt suffers;
- Hole patterns are irregular and differ product to product: adjustment cannot keep up with the variation and setting time exceeds the benefit;
- Small batches with many variants: fixture and setting cost cannot be amortised, and a coordinate machine moving point to point is more economical;
- Fastening specifications vary widely: different torques and screw sizes in a single press stroke are very hard to reconcile process-wise.
A sensible order of judgement is: number and distribution of positions first, then variant count and batch size, then consistency of specification. If any one of the three is clearly unfavourable, the coordinate approach is usually the safer choice.
6. Acceptance checks
- Run first-off with the densest product, confirming every position reaches depth consistently;
- Pay particular attention to fastening depth at the outer spindles — the edges are usually where deflection is greatest;
- Re-measure spindle pitch after a period of running: heat and vibration cause small shifts in the connecting plate;
- Re-establish the zero position after changeover; never carry over the previous product's coordinates.
7. Frequently asked questions
Q1: How small can spindle pitch be?
It depends on screw size and spindle type. With the same specification and low torque, spacing can be quite tight. With larger screws that need sleeves and grippers, pitch must be increased. The figure has to be confirmed against workpiece and process — do not extrapolate from bit diameter alone.
Q2: How much deviation can a floating bit absorb?
Floating travel is typically 0.5 to 2 millimetres, intended to absorb small variations in part flatness and location. It does not replace fixture location; excessive floating travel lets the bit slip during fastening.
Q3: Multi-spindle or coordinate machine?
Look at position density and variant count. Concentrated positions with stable batch size favour multi-spindle efficiency. Scattered positions, many variants and small batches favour the flexibility of a coordinate machine. The two can also be combined: multi-spindle heads mounted on a coordinate platform, gaining both density and travel.
Q4: Do multi-spindle machines need a demanding air supply?
Simultaneous spindle action means high instantaneous air consumption. Based on the company's current project experience, multi-spindle machines commonly use a 0.8 kW class power configuration, with supply pressure held above 0.5 MPa at adequate flow, and pipe diameter and receiver sized for peak demand. Specific requirements depend on the workpiece, spindle count and final solution.
— End of Article —
Author: Chisu Automation Technical Team
Published: November 6, 2026
Keywords: multi-spindle fastening, spindle pitch, minimum centre distance, interference avoidance, fixture design, multi-axis screwdriving machine