Product Updates

CCD Vision-Guided Fastening: Choosing Between Fixture Positioning and Vision Positioning

📅 2026-10-26

In fastening automation projects, “adding vision” is often discussed as a single decision. In engineering terms, however, it covers two very different tasks: finding the screw position before fastening, and judging the result afterwards.

1. Two different problems: inspection versus positioning

  • Vision inspection — after fastening, a camera confirms the result: whether the screw is seated, whether any position was missed, whether appearance is acceptable. It answers “how do we judge what was done”.
  • Vision positioning — before fastening, a camera locates the target screw positions and passes coordinates to the motion system. It answers “where should the machine move”.

They can be adopted separately or together. This article deals with the second: how a fastening system finds screw positions when workpiece location itself is uncertain.

2. What fixture positioning can achieve

Fixtures are the most common and most economical positioning method. The logic is straightforward: the part is placed on a shaped base and mechanically constrained so that screw positions land on the same coordinates every cycle.

Whether a fixture works depends on three things:

  • Whether the part has a stable, repeatable datum face or locating hole;
  • Incoming consistency — how much dimensional and positional variation exists within a batch;
  • Changeover frequency — a fixture is dedicated to one product, so a new product usually means a new fixture.

Where all three conditions hold, fixture positioning often delivers better accuracy and takt than vision, and long-term stability is easier to guarantee because there are no cameras, lighting or algorithms in the loop.

3. When vision positioning should be evaluated

Any one of the following signals justifies assessing vision guidance at the solution stage.

1. No reliable datum, or incoming position varies

Typical cases are circular, contoured, soft or decorative parts. Such parts can rotate or shift even inside a fixture. Where the upstream process is painting, moulding or stamping, actual position may differ from part to part.

2. Fixture-based alignment becomes too costly

Where screw positions are numerous and irregular, or the outline is complex, tooling becomes elaborate and is scrapped as soon as the product changes. Locating accuracy requirements also rise sharply.

3. Fastening must be corrected in real time

In some processes the critical relationship is between the screw position and the part outline. Vision can locate holes relative to product features rather than relative to the machine coordinate system.

4. Many product variants with frequent changeover

Changeover with vision means switching recipes — recognition templates and coordinate sets are stored in the product program and recalled from the touchscreen, without replacing tooling.

4. The vision-guided fastening workflow

A complete vision-guided fastening system follows four steps.

Identify → Locate → Fasten → Check

  • Identify: the camera captures an image and determines which model is present and whether orientation is correct;
  • Locate: target positions or part features are extracted in image coordinates and converted to machine motion coordinates;
  • Fasten: the motion platform drives the fastening head point by point, with torque and rotation monitoring available;
  • Check: the result is confirmed, and any abnormality triggers an alert and stop or mark.

Two common configurations are XYZ-coordinate vision fastening and multi-axis vision fastening. The former moves point by point on a motion platform and suits scattered positions and frequent product changes; the latter combines vision with multi-axis heads for workpieces with concentrated positions that benefit from simultaneous operation.

5. How to configure a vision solution

The following items should be defined together with part samples and process requirements — not after the equipment has been selected.

  • Vision accuracy: depends on camera resolution, lens field of view and the accuracy actually required;
  • Camera count: a single camera moving to each position versus multiple cameras covering zones directly affects takt;
  • Lighting: for reflective, dark or heavily textured parts, lighting design is often more critical than camera selection;
  • Motion and fastening: coordinate platforms combined with electric or servo screwdrivers, selected to the process;
  • Takt: recognition time must be included in overall cycle time, not only the fastening time.

6. Frequently asked questions

Q1: With vision, are fixtures no longer needed?

No. Vision solves “can we find it”, while fixtures solve “can we hold it”. Pressing operations and processes with significant reaction forces still need reliable clamping and support; the two normally work together rather than replace each other.

Q2: What accuracy can vision positioning achieve?

Accuracy depends on field of view, camera resolution and calibration quality, and must be assessed for the specific part; there is no universal figure. The larger the field of view, the more real-world size each pixel covers, and the harder high accuracy becomes — which is why large parts often use zone cameras with local fine positioning.

Q3: Does a new product require recalibration?

If the camera position relative to the machine has not changed, it is usually enough to capture a new recognition template in the product program and save the coordinate set; switching back to an earlier product simply recalls it.

Q4: Does vision guidance slow the takt?

Recognition does consume time, but it can be reduced with shorter exposure, restricted regions of interest and parallel cameras. Where changeover is frequent, the time saved in changeover and debugging is often more valuable.

— End of Article —

Author: Chisu Automation Technical Team

Published: October 26, 2026

Keywords: CCD vision positioning, vision-guided fastening, fixture positioning, automatic screw fastening machine, fastening accuracy

← Back to News
📞 Contact
After-sales: 400-876-8800
💬 Pre-sales 🔧 After-sales 📥 Downloads
⬆️ Top